Press SET button and the already set wheel circumference will blink on the sub-display.
Select the (O) mode and stop the measurement. The first wheel circumference measurement will be displayed for a few seconds, then the second setting will appear. (Refer to the explanation of Auto Mode function.) While keeping the right button pressed, press the SET button. Selecting one of the two Wheel Circumference (Fig.7) Set to a desired wheel circumference in the same manner as the first circumference setting and press SET button to complete the setting. The wheel circumference 2030mm is displayed and blinks(fig.6). If you want to set a second circumference, press the left and right buttons together before pressing the SET button. Once you reach the setting you want, press the SET button. To change the number rapidly keep the button pressed. If you want to change, press either the right button to increase or left button to decrease the number. If you want to enter 2155mm and 2030mm, simply press the SET button.
The (A) wheel circumference 2155mm (standard for 27 inch tire) will blink as shown in fig.5. Two wheel circumferences, (A) 2155mm and (B) 2030mm, have been set before the cyclocomputer left our factory. One main unit can be used on two bicycles subject to buy another set of bracket and sensor. This cyclocomputer is able to memorize two different wheel circumferences. Setting the Wheel Circumference (Fig.5.6) Select any speed scale as desired and press SET button to complete the setting. "km/h" and "mile/h" are displayed alternatively each time the right button is pressed. When the AC button is pressed and all displays illuminate then the "mile/h" appears as shown in fig.4. Or, the "Setting Values Cross Reference Table" can help you to find out an approximate wheel circumference according to tire size. This measure is your actual wheel circumference. Mark the ground at the end of one revolution and then measure the distance between the two marks.
#CATEYE ENDURO 8 CYCLOCOMPUTER FULL#
Then ride the bike one full wheel revolution.
#CATEYE ENDURO 8 CYCLOCOMPUTER HOW TO#
How to measure the exact Wheel Circumference (L)(Fig.3)įirst, adjust tire pressure and then put a mark on the tire tread and the ground simultaneously. User must make the following setting according to instructions before the cyclocomputer can be used properly. (In the total distance display mode, the current wheel circumference (A) or (B) is shown.) MAIN UNIT PREPARATION Stored data of trip distance (D), elapsed time (T), average speed (A) and maximum speed (M) are all reset to zero. Press left button to select any mode except total distance (O) and press left and right buttons together. (refer to Main Unit Preparation) Reset Operation: (Fig.2) Once this button is pressed and all memory is erased, it will be necessary to set the wheel circumference, time, etc. This button should be pressed only after replacing the battery or when irregular display of information occurs due to static electricity, etc. After all displays illuminate, the "mile/h" symbol illuminates. When this button is pressed, all the data stored in memory is cleared. Select the (T),(A) or (D) mode, then press the SET button.ĪC (All Clear) Button (bottom right button) Stop the measurement in ( ) mode, then press the SET button. Stop the measurement in the (O) mode, then press the SET button. Note: This button does not function if the auto mode function is set to ON. During measurement the speed scale symbol blinks. Whenever this button is pressed, start and stop are repeated. Measurement of trip distance, elapsed time and average speed is started or stopped when the start/stop button is pressed. Note: If this button is kept pressed for more than 2 seconds, display appears. Whenever this button is pressed, the mode display changes in the order shown in fig.1, and the data is displayed on the sub-display. These buttons are used as follows: Mode Button (top left button) Two buttons are provided on the top of the main unit and two on the bottom. 14 Setting Values Cross Reference Table.10.1 How to Set On/Off the Auto Function.10 AUTO (AUTOMATIC START/STOP) FUNCTION.7.2 How to replace battery in Sensor (Fig.21).7.1 How to replace battery in Main Unit (Fig.20).4.1 How to Mount the Sensor on the Right Front Fork Leg.(fig.11).3.5 How to reset the Wheel Circumference.3.4 Selecting one of the two Wheel Circumference (Fig.7).3.3 Setting the Wheel Circumference (Fig.5.6).3.1 How to measure the exact Wheel Circumference (L)(Fig.3).2.4 AC (All Clear) Button (bottom right button).2.2 Start/Stop Button (top right button).
0 kommentar(er)
